The Philio Insert Switch allows controlling two independent loads both wirelessly via Z-Wave and locally utilizing a traditional wall switch. Thanks to its calibration technology the PAN06 cannot only be used to switch AC devices ON and OFF, it also works perfectly with many kind of light, e.g. incandescent, fluorescent and LEDs. In addition to this, the PAN06 can be connected to 12V/DC, which makes it possible to switch 12V MR-16 light as well. The device is placed in a wall box right behind the normal switch. The switch is not longer directly connected to the load but acts as input device for the insert that is controlling the load. This device is designed for a 3 wire system and needs a neutral wire in the wall box.

This in-wall dual relay switch module is a transceiver which is a Z-Wave Plus enabled device and is fully compatible with any Z-Wave enabled network.Mini size design let the module can easily hide itself into the wall box and that will be good for the house decoration. There are many kind of application by using the module to switch AC power On and Off, one main application is the light control. The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of light like incandescent, fluorescent and LED light.This in-wall switch module is able to detect Instant power wattage and overload current (7.5A) of connected light or appliances. When detecting overload state, the Module will be disabled and its On/Off button will be lockout of which LED will flash quickly. However, disconnect and re-connect the Module will reset its overload condition to normal status.

The Philio Roller Shutter Controller insert allows controlling motors for jalousies and blinds both via Z-Wave wirelessly and locally utilizing a traditional wall switch.
The device is placed in a wall box right behind the normal switch. The switch is not longer directly connected to the load but acts as input device for the Philio insert that is controlling the load.
This relay is able to detect the position of the shutter by using the patterned power measuring method. So it can be remote controlled not only fully up or down, but also can be adjusted to e.g. 30% or 50%. And when manual controlled by using the push button, the controller also can memorize the position and send the new shutter position to its controller (ex. IP-Gateway).
The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of roller shutter.

Transform any home into a smart home with the Philio PAD02 Z-Wave Smart Dimmer Socket. The dimmer socket can be easily adapted to your current lighting devices, uses your existing lamp (E27 socket), and provides Z-Wave wireless and with remote control of overhead lighting. Use the dimmer feature to customize the lighting output and create the perfect ambiance for any room. Providing ultimate flexibility, the Philio Z-Wave Smart Dimmer Socket allows you to operate the lighting by itself or easily integrate the socket with two-way, three-way or four-way wiring configurations by adding the Philio Smart Switch Modules for Z-Wave. Take control of your home lighting with Philio Z-Wave Smart Lighting Controls!
Easily adapt to any standard lamp E27 socket with the Philio Z-Wave Smart Dimmer Socket to turn lighting on/off or adjust dim levels with your mobile device or computer using any Z-Wave certified gateway. Can be controlled in groups of multiple lights or used to create dimmable ambient interior lighting scenes.

The Z-Wave 3 in 1 sensor (PHI_PSM01) is designed with three detection sensors:

• Door/windows;
• Temperature sensor;
• Luminosity sensor.

The sensor consists of two parts; a Detector and a Magnet. They are designed to be fitted to doors or windows with the Magnet mounted on the opening part and the Detector mounted on the fixed frame. Opening the protected door/window will remove the magnetic field, trigger the detector and generate an alarm condition, (if the system is armed). The sensor can also applied to automatic light control, one scenario is to get the illumination lux level from built in illumination sensors and send a signal to Z-wave switch to turn the light on once we open the door when the room is dark. Every time when Door/Window trig, the sensor will also send temperature and illumination value as well. Also the temperature will send out the value when temperature changes. Note: The illumination sensor yet does not work with Fibaro Homecenter 2 and Zipato Zipabox.

The Z-Wave 3 in 1 sensor (ZWphiPST02-1B) is designed with three detection sensors:

• PIR/Motion;
• Temperature sensor;
• Luminosity sensor.

The detector can be used as a security device or home automation device. When the detector is cooperated with security appliances, the detector is acting as a security device by detecting changes in infra-red radiation levels. If a person moves within or across the devices field of vision, a trigger radio signal will be transmitted to cause full alarm condition in order to frighten intruders away. Alternatively, when the detector is worked with Z-Wave Controller, the detector can be set to perform the role of home automation device by detecting both changes in infra-red radiation levels and percentage of lux levels. Every time when PIR trig, the sensor will also send temperature and illumination value as well. Also the temperature will send out the value when temperature changes. Note: The illumination sensor does not work with Fibaro Homecenter 2 and Zipabox yet.

The Z-Wave 4 in 1 sensor (ZWphiPST02-1A) is designed with three detection sensors:

• Door/window sensor;
• PIR/Motion;
• Temperature sensor;
• Luminosity sensor.

Thanks to this the PSM02 can be uses as a security device or home automation device, e.g. to send an alarm when a motion is detected, turn the light on/ off automatically at night or to adjust the heater. The product consists of two elements - the detector and the magnet. The magnet is mounted on the moving part of the window or of the door. The other part is placed on the frame. Note: The illumination sensor does not work with Fibaro Homecenter 2 and Zipabox yet.

Zipato Flood Multisensor 3 in 1 integrates flood, temperature and humidity sensors in one device. Zipato Flood Multisensor 3 in 1 offers elaborate security and ambient sensing options. Multifunctional nature of this product allows you to informed about water leakages and potential flood disasters, as well as to measure temperature and humidity levels. When used with Zipato home automation controllers it can be part of any automation scenario created using Zipato Rule Creator. Accordingly it can be used to automatically trigger other Z-Wave devices when activated.

The new Philio Motion Detector in small ball design detects movements at a distance of up to 12 meters. The sensor can be easily installed on the ceiling or a wall thanks to a supplied magnetic holder. Thanks to the unique and descretely design, you can place the sensor anywhere to automate your light. Then your light switches on only when the movement is detected, and if there is no person in the room, the lamps are not switched on.

The sensor also includes a lens cover. With the cover, you can hide an area which is not to be detected by the motion detector.

In addition, the sensor is suitable for outdoor use. This allows you to extend your automation and alarm system to the outside. The sensor is battery operated and can be easily added to your Z-Wave Smart Home System.

The compact sensor in ball design recognizes motion in a distance up to 12 meters and can be installed quite easily and individually at ceilings or walls.
This allows you to place the sensor descretely next to your lighting and automate your lights.

In addition, the sensor is suitable for outdoor use. This allows you to extend your automation and alarm system to the outside. The sensor is battery operated and can be easily added to your Z-Wave Smart Home System.

The compact sensor in ball design recognizes motion in a distance up to 12 meters and can be installed quite easily and individually at ceilings or walls.
This allows you to place the sensor descretely next to your lighting and automate your lights.

In addition, the sensor is suitable for outdoor use. This allows you to extend your automation and alarm system to the outside. The sensor is battery operated and can be easily added to your Z-Wave Smart Home System.

The Philio Round Recessor is made to mount motion sensors on the ceiling. The Fibaro motion sensor and the Philio outdoor motion sensor fit perfectly into the brackets. So the motion sensor is installed in the right position and through a firm and reliable attachment.

The Philio Square Recessor is made to mount motion sensors on the ceiling. The Fibaro motion sensor and the Philio outdoor motion sensor fit perfectly into the brackets. So the motion sensor is installed in the right position and through a firm and reliable attachment.

Valid for the references: ZWPHI PAN08 - Z-Wave Plus Relay Insert Blind ZWPHI PAN06 - Z-Wave Plus 2 Relays Insert Refer in the observations field the desired quantities and references.

The Philio Smart Keypad with an elegant glass touch panel can be included in your Z-Wave network to increase the security in your home. The smart device support Z-Wave Multi-Functions Smart Switch to report the current key status and setup Arm/ Disarm.