When an incandescent lamp is plugged onto this module, it can be controlled using any X10 controller or locally via the ON/OFF button on the module.
Simply press the ON/OFF button on the module to toggle between ON and OFF states or send an X10 command to it.
Using an X10 controller, this module can also respond to the X10 Bright/Dim command.

EOL (end of life) equipment:
Alternatives:
INS 2453-422 Din rail actuator

The X10 DIN rail switch is a remote controlled relay. Discretely installed at the junction box, it switches hard-wired circuits with several switches (e.g. hallway lighting). The internal relay can be tripped either by external latched or momentary action wall switches or by an X10 controller.

The AD10E responds to STANDARD X10 protocols: "All units off" from any X10 controller set to its house code, regardless of unit code. Or alternatively, by individual unit control using "On" and "Off". When the relay is energized, the LED above the slide switch is illuminated.

The LW12 is an in-wall module with built-in dimmer that can be installed behind existing momentary switches or wall outlets.

The LW12 can be controlled with X10 signals via the mains or a momentary switch connected to the LW12. The LW12 has a memory setting for the last dimmer setting and uses SoftStart and SoftDim. The LW12 is the only X10 module that doesn't use a zero wire. This means it can replace a switch without having to use any extra wiring.

The AW 12 reacts to the standard X10 commands that are: "All Units On", "All Units Off", "All Lights Off" from any X-10 controller set to its house code regardless of unit code or alternatively individual unit control by "On" an "Off" commands.

House code and unit code are programmed using any X10 compatible controllers. There is an EEPROM that stores the house and unit code even when the power is cut.

We would like to point out that this article is not a new product. The product has got the complete functionality and can be used without restriction. However, the product may have the following characteristics:

broken seal,
damaged packaging,
no original packaging
missing accessories,
minimal signs of wear,
no current software version.

We offer a guarantee of one year. With a possible return you receive a credit note, there is no exchange of the product. The picture may not correspond to the scope of delivery of the product.

Dimming actuator for installation behind retractive switches and wall sockets or in distribution boxes.
Suitable for remote or on-site operation of lighting.

EOL Equipment. Alternative: INS 2443-422 - Micromodule On/Off

The AW12 in-wall module is small enough (46 x 46 x 17 mm) to be mounted behind any standard wall switch, even most designer switches.

It is an X10 receiver module that can be controlled by any X10 controller or remote control sending X10 signals. The internal relay can also be tripped by external latched or momentary action wall switches. If a push button is used, the internal relay changes its status after a momentary press (< 1,75s). If a latched switch is used, the internal relay changes it status after 1.75s. This module is able to be used on a conventional commutation without changing the existing switches.

The AW 12 reacts to the standard X10 commands that are: "All Units On", "All Units Off", "All Lights Off" from any X-10 controller set to its house code regardless of unit code or alternatively individual unit control by "On" an "Off" commands.

House code and unit code are programmed using any X10 compatible controller. There is an EEPROM that stores the house and unit code even when the power is cut.

EOL Equipment. Alternative: INS 2443-422 - Micromodule On/Off

The LMM32 module allow to dim two individual lamps, being small enough (43 x 47 x 18,9 mm) to fit behind a wall switch or junction box. It allows to control both internal relay either using any conventional electric switch (push buttons are not supported) or remotely, using any X-10 compatible controller.

This module has a special feature which allows setting 16 distinct X-10 addresses to each internal relay. This is very useful to create macros.

We would like to point out that this article is not a new product. The product has got the complete functionality and can be used without restriction. However, the product may have the following characteristics:

broken seal,
damaged packaging,
no original packaging
missing accessories,
minimal signs of wear,
no current software version.

We offer a guarantee of one year. With a possible return you receive a credit note, there is no exchange of the product. The picture may not correspond to the scope of delivery of the product.

EOL equipment: alternatives: INS_2444-422 - Micromodule Open/Close (for shutters) from INSTEON is X10 compatible.